在厅门装潢的领域里，我们有多种工艺可供选择：从现代感的不锈钢包覆，到色彩丰富的贴膜，再到经典耐用的喷漆工艺。然而，在这些方法中，不锈钢包覆以其经济性、美观性以及耐用性脱颖而出，成为最受欢迎的选择。您可能会好奇，这种不锈钢包覆是如何做到既美观又牢固的呢？是否存在脱落的隐患？为了解答这些疑问，今天，我们将带您走进施工现场，一睹我们专业安装师傅的精湛技艺，看看他们是如何将不锈钢板巧妙地包覆在门上，确保其既美观又安全。跟随我们的脚步，一起见证厅门变身的过程，探索不锈钢包覆背后的工艺秘密，让您对厅门装潢有更深的认识和了解。

　　In the field of hall door decoration, we have a variety of techniques to choose from: from modern stainless steel cladding, to colorful film coating, to classic and durable spray painting techniques. However, among these methods, stainless steel cladding stands out as the most popular choice due to its economy, aesthetics, and durability. You may be curious about how this stainless steel coating achieves both aesthetics and durability? Is there a risk of detachment? To answer these questions, today we will take you into the construction site to witness the exquisite skills of our professional installers, and see how they cleverly wrap stainless steel plates around doors to ensure both aesthetics and safety. Follow our footsteps and witness the transformation process of the hall door together, explore the secrets behind the stainless steel coating, and gain a deeper understanding and knowledge of hall door decoration.

　　01清洁准备

　　01 Cleaning Preparation

快盈v3　　门板拆卸后，清除表面灰尘、脏污（如水泥、油污等），并去除保护膜，确保粘接面清洁，同时妥善保管锁芯。

　　After disassembling the door panel, clean the surface dust and dirt (such as cement, oil stains, etc.), remove the protective film, ensure the bonding surface is clean, and properly store the lock cylinder.base64_image

　　02粘贴胶带

快盈v3　　02 Adhesive tape

快盈v3　　在不锈钢门皮或门基板上粘贴胶带，上下两端各两条，间距约30mm；竖向胶带间距为30-50mm，根据门板宽度适当调整，确保胶带靠近边缘。

　　Stick adhesive tape on the stainless steel door panel or door substrate, with two strips on each end at a distance of about 30mm; the vertical tape spacing is 30-50mm, adjusted appropriately according to the width of the door panel to ensure that the tape is close to the edge.

　　03撕除胶带

　　03 Peel off the tape

　　撕去胶带保护层，在间隙和接缝处均匀涂抹结构胶，避免过量造成鼓包。检查胶带，排除气泡，确保贴合平整，尤其是镜面材料，防止产生变形。

　　Tear off the protective layer of the tape and evenly apply structural adhesive to the gaps and seams to avoid excessive bulging. Check the tape, eliminate bubbles, ensure a smooth fit, especially for mirror materials, to prevent deformation.

　　04外包门板

　　04 Outsourced door panel

快盈v3　　可选择平放或竖放操作，确保不锈钢门皮下端与门基板下端对齐，压实边缘后贴合表面。

　　You can choose to place it horizontally or vertically to ensure that the lower end of the stainless steel door skin is aligned with the lower end of the door base plate, and after compacting the edges, it fits the surface.

　　05清理表面

　　05 Cleaning the surface

快盈v3　　粘贴完成后，用干净抹布擦拭整个表面，以增强外包面板与基板的粘合，防止灰尘进入导致脱胶。

　　After pasting, wipe the entire surface with a clean cloth to enhance the adhesion between the outer panel and the substrate, and prevent dust from entering and causing delamination.

　　06精准打孔

快盈v3　　06 Precise Drilling

　　确认外包面板与基板完全贴合后，开始精准打孔，并使用抽芯铆钉加固，注意避免在可视面上打孔。

　　After confirming that the outsourcing panel is fully attached to the substrate, begin precise drilling and reinforce with pop rivets, taking care to avoid drilling on visible surfaces.

　　07沉孔处理

　　07 Sinking hole treatment

快盈v3　　打孔后，使用较大钻头进行沉孔处理，及时清理孔内及孔周边的铁屑，然后使用抽芯铆钉（沉头铆钉）固定。

　　After drilling, use a larger drill bit to sink the hole, clean the iron filings inside and around the hole in a timely manner, and then fix it with pop rivets (countersunk rivets).

　　08碰珠、锁芯安装

快盈v3　　08 Installation of collision beads and lock cores

快盈v3　　根据原门板的锁孔和碰珠位置，精确开孔，注意保留原碰珠橡胶，锁孔应为双D型，避免使用过大的开孔器导致锁芯安装不稳。09清理、检查及安装

　　According to the lock hole and bead position of the original door panel, accurately drill the hole, and pay attention to retaining the original bead rubber. The lock hole should be double D-shaped to avoid using too large a hole opener that may cause unstable installation of the lock core. 09 Cleaning, Inspection, and Installation

快盈v3　　最后清理所有铁屑和污垢，检查外包门板的安装情况，确保所有辅助部件重新安装到位，与拆门师傅协作完成门板安装，结束外包工序。通过这一系列精细的工艺步骤，我们承诺为每一位客户提供安全、美观、耐用的电梯厅门包门解决方案。

　　Finally, clean all iron filings and dirt, check the installation of the outsourced door panels, ensure that all auxiliary components are reinstalled in place, collaborate with the door dismantling master to complete the door panel installation, and end the outsourcing process. Through this series of meticulous process steps, we promise to provide every customer with a safe, beautiful, and durable elevator hall door package solution.

　　本文由 济宁电梯门套加工定制  友情奉献.更多有关的知识请点击  http://stjbjjd.cn/   真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This article is a friendly contribution from Jining Elevator Door Frame Processing Customization For more related knowledge, please click http://stjbjjd.cn/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.